WhetGuide
An open Lansky sharpening kit with colored hones and honing oil beside a Mercer bread knife on a wooden board with a cut sourdough loaf

How to sharpen a serrated knife

Serrated knives stay sharp for a long time, but they do get dull. The method is simple: sharpen each scallop on the beveled side with a tapered rod, then take the burr off the flat side. This guide walks through the rod method and the faster options, then steak knife sets and combo-edge folders, and says when a new knife is the better deal.

How we pick · Updated · We earn a commission when you buy through our Amazon links.

To sharpen a serrated knife, run a tapered sharpening rod through each scallop on the beveled side, matching the existing angle, until you feel a slight burr on the flat side; then remove that burr with a few light passes on the flat side. It takes 10 to 15 minutes for a bread knife. If that sounds fiddly, a Spyderco Sharpmaker or an electric sharpener with a serrated setting gets you most of the way faster. Before any of it, wash the blade: a lot of "dull" bread knives are only packed with starch. This page covers the rod method in detail, the faster tools and what each one actually touches, steak knife sets, combo-edge pocket knives, and the cases where a new knife is the better answer.

↑ Sections ↑ Back to all sections

Quick answer: a serrated knife in eight steps

Clean it, find the beveled side, fit the rod to the scallop, sharpen each scallop until it raises a burr, then take the burr off the flat back. Everything else on this page is detail on those five moves.

Five numbered steps: clean and test the knife, find the beveled face, fit the tapered rod to the scallop, sharpen each scallop to a burr working heel to tip, and deburr the flat back on a fine stone
Every method on this page follows these five moves. Faster tools change how step 4 happens, not the order.
  1. Wash and dry the blade, then cut a tomato or a crusty loaf. If it cuts cleanly now, it was only gummed up (how to tell).
  2. Find the beveled side: the face with the scallops ground into it. The other face is usually flat (which side).
  3. Color the bevels of the scallops with a permanent marker.
  4. Slide a tapered rod into the first scallop until its thickness fills the curve (rod size).
  5. Tilt the rod to lie flat on the bevel, then make short, light strokes out toward the edge, rolling the rod a little so it sweeps the whole curve (step by step).
  6. Stop when the ink is gone and you can feel a slight burr on the flat back. Move to the next scallop, heel to tip.
  7. Lay the flat back dead flat on a fine stone or ceramic rod and make one or two light passes to remove the burr (deburring).
  8. Test it on a tomato, a crusty loaf or a sheet of paper (test cuts).

Short on time or doing several knives? The Sharpmaker corner method does the points and the scallops together. The same steps fit on one card in the printable cheat sheet.

A Victorinox Fibrox bread knife lying on a wooden board beside a sliced crusty loaf and crumbs, with a Mercer wavy-edge bread knife on the granite counter behind it, a folded striped linen towel and a WhetGuide.com mug
A bread knife that tears the crust instead of slicing it is the usual reason people go looking for this page.
↑ Back to all sections

First, look at the edge

Turn the knife over in good light. On most serrated kitchen knives you'll see the scallops cut into one face of the blade, while the other face is flat. That means the knife is ground on one side, and the beveled face is the one you sharpen.

Side view of a bread knife labeled handle, heel, spine, tip, beveled face, point or tooth and gullet or scallop, with the cutting edge in red, plus an end view showing one beveled face and a flat back
The words the rest of this page uses. The red line is the edge you're sharpening; the gray crescents above it are the ground bevel of each scallop.

A few terms, because guides use them loosely:

  • Points, or teeth: the sharp tips between the scallops. They touch the food first and take most of the wear.
  • Gullets, or scallops: the curved hollows between the points. Their edges do the slicing once the points have broken through a crust.
  • Beveled face: the side where each scallop is ground at an angle. This is where the sharpening happens.
  • Flat back: the other face. It runs flat from the spine right down to the edge. Knife Den gives this as the quickest tell: the flat side runs the full height of the blade, and the other side angles in where the serrations start.

The points also explain why a serrated knife keeps cutting so long. Only the points ride on the board and on the crust, so the scallop edges behind them barely touch anything hard. The Takeout puts it the same way: the edge is only partly in contact at any moment. The flip side is that once the points round over, the knife skates, and once the scallop edges dull, it tears.

Serrated edge anatomy and where the rod goes A row of scallops along a blade edge, with a tapered rod sitting inside one scallop. Labels show the points (teeth), the scallops (gullets) and the beveled side. point (tooth) scallop tapered rod: slide in until it fills the scallop beveled side facing you
Each scallop is sharpened separately. Slide the rod in until its diameter matches the scallop.
↑ Back to all sections

Is it dull, or just gummed up?

Check this first. Bread starch and tomato skins pack into the gullets and dry there, and so do cheese and grease. A blade with full gullets slides over food the way a dull one does. Made In lists the same two signs of a knife that needs sharpening, tearing or squishing food, and both can come from residue.

Three close-ups of a serrated edge: healthy with sharp points, dull with flattened points that catch the light, and gummed up with residue packed in the scallops, each with what it looks like, a home check and the fix
Up close the three look different, and only the middle one needs a sharpener.
  1. Wash the blade in hot soapy water. Scrub the gullets with a stiff nylon brush, moving from the spine toward the edge with the edge facing away from you.
  2. For dried-on residue, a rubber abrasive eraser block lifts it without scratching. Lansky sells one.
  3. Dry it completely.
  4. Cut a ripe tomato with no downward pressure. A healthy edge bites the skin at once. Then try the crust of a day-old loaf.
  5. Hold the edge under a bright light, point toward you, and look straight down it. Rounded points catch the light as tiny bright dots. Sharp points don't.

If the knife cuts after cleaning, put the sharpener away. If it still skates on the tomato, crushes the loaf, or shows bright dots along the points, read on. One more check worth doing: if only the front third of the blade is dull, that's where you cut most. Sharpen just those scallops.

↑ Back to all sections

Which side do you sharpen?

The beveled side, and only the beveled side. On a typical bread or steak knife the scallops are ground into one face at an angle, while the back face stays flat like a chisel. Sharpening Supplies and Outdoor Life agree, and so does Work Sharp: sharpen the scalloped face, then just remove the burr from the flat back.

Three cross-sections: a serrated edge beveled on one face with a flat back, a plain edge beveled on both faces, and a serrated edge with scallops ground into both faces, each with a note on what to sharpen
One beveled face is the common case. A few serrated knives are ground on both faces; give each side the same light rod work.

How to tell for sure on your own knife:

  • Look at the blade face-on, from each side, in raking light. The beveled side shows each scallop as a little ground crescent. The flat side looks like the rest of the blade right down to the edge.
  • Run a fingernail gently from the spine down the flat face toward the edge (across it, never along it). On the flat side your nail meets no step. On the beveled side it drops into each scallop's grind.
  • Check both sides. Some knives, including many inexpensive steak knives and a few bread knives, show scallops ground into both faces. That edge is two-sided, and both faces get the rod.

Don't assume which face it is from another knife you own. Left-handed bread knives exist, and makers don't all grind the same face, so check each knife once and remember it.

A serrated edge showing scallops ground on one side
Look for the side with the scallops ground in. That's the side to sharpen.
↑ Back to all sections

What you need

The one real tool is a tapered rod in ceramic or diamond. It's narrow at the tip and thicker toward the handle, so a single rod fits scallops of different sizes. Fine ceramic is gentle. Diamond cuts faster if the knife is very dull. Add a permanent marker so you can see where metal is coming off, and work on a stable surface under good light.

You may already own a serrated tool without knowing it. The Work Sharp Precision Adjust Elite comes with a conical ceramic rod for serrations, the Lansky Professional kit includes a serrated medium hone, and the Work Sharp Guided Field Sharpener has a ceramic rod. If you're still choosing a tool, our best knife sharpeners for serrated knives sorts them by what actually reaches the scallops.

Four tapered sharpening tools lying flat on a pale wooden board: a folding diamond rod in a gray translucent case, an AccuSharp tapered diamond rod beside its black cap, a blue-hinged Lansky folding rod and a SHARPAL pocket sharpener with a spare rod section
Loose tapered rods: two folding, one with a fixed handle, one pocket tool with a rod at the end. Any of them fits a bread knife's scallops.

The full kit, most of which is already in a kitchen drawer:

ItemWhat it doesMust have?
Tapered rod, ceramic or diamondSharpens inside each scallopYes, unless you use a Sharpmaker or a guided system's rod
Permanent markerShows where steel is coming off and when a scallop is doneYes
Fine stone, ceramic rod or stropRemoves the burr from the flat backYes; a fine ceramic rod held flat works
Bright lampShows glinting points and where the ink is goneYes
Damp towel or rubber matKeeps the knife and your hand from slippingHelpful
10x loupeLets you see the burr and rounded points on fine teethHelpful for steak knives
Tomato, crusty loaf, paperTest cutsYes

Diamond or ceramic rod?

Both work. Pick by how dull the knife is and how hard you tend to press.

RodCutsGood atWatch out for
Diamond tapered rodFastA badly dull bread knife, hard steels, chipped pointsEasy to overdo; Chowhound suggests single-direction strokes with diamond
Ceramic tapered rodSlower, finerTouch-ups, a knife that's only a little dull, finishing after diamondBrittle; it can chip or snap if dropped
Sharpmaker stone cornersMedium or fine ceramicSeveral serrated knives done one wayVery dull edges take a while on ceramic
Sandpaper on a dowelDepends on gritA one-off fix with no rodPaper tears and rounds the points if you press
Three cards: a badly dull or chipped knife starts on a diamond tapered rod and can finish on ceramic, a slightly dull knife needs only a ceramic tapered rod, and several serrated knives go faster on Sharpmaker corners
Pick the starting rod by the state of the edge. Diamond is quick but easy to overdo; ceramic cuts slowly to a finer finish, but it is brittle.

If you only buy one, a fine or medium diamond tapered rod handles both a dull bread knife and the occasional steak knife. Knife Den recommends ceramic for a polished finish, which is a fair second step but not a must.

↑ Back to all sections

Choosing the rod size: fit the taper to the scallop

Size is the part most guides skip. A rod that's too thin only touches the bottom of the scallop and cuts a groove there. A rod that's too thick can't get in at all; it rides on the points and slowly widens the scallop. Outdoor Life puts it as keeping strokes short so you don't crater the center, and the right diameter is the other half of that advice.

A tapered sharpening rod running from about 1/16 inch at the tip to about 1/4 inch at the base, with fine, medium and large gullets placed over the part of the taper that fits each, and two failure cases: a rod too thin that grooves the scallop and a rod too thick that rides on the points
Slide the rod in until it fills the curve. That spot on the taper is where you work for that scallop size.

The only published size range we found is for the DMT Diafold serrated sharpener, which Sharpening Supplies describes as tapering from roughly 1/16 inch to 1/4 inch. That covers fine steak knife teeth at the tip and wide bread knife scallops near the base. Most tapered rods sold for serrations cover a similar spread, but makers rarely print the numbers, so fit it by eye:

  1. Hold the knife flat on a towel, beveled side up.
  2. Lay the rod across the first scallop, tip first, then slide it in along its length.
  3. Stop when the rod touches both sides of the curve at once. That's the working spot.
  4. Keep your strokes inside a short band around that spot. On a long rod, a thumb or a piece of tape marks it.
Scallop sizeTypical knifeWhere on the taperOther tools that fit
Large and deepBread knifeToward the baseSharpmaker corner, guided-system serrated rod
MediumUtility and tomato knives, smaller bread knivesMiddleSharpmaker corner
Small and tightSteak knife, combo-edge folderToward the tipCorners of Sharpmaker stones, thin pocket rods
Very fine (micro-serrated)Some budget steak knivesVery tip, if at allOften not worth sharpening; replace the knife
Mixed sizesDouble-serrated bread knivesMove along the taper as the scallops changeSharpmaker corner handles the mix

If the rod fills the scallop at one spot but the scallop next to it needs a different spot, that's normal on hand-ground or double-serrated knives. Just move along the taper as you go. Knives and Tools gives the same rule in its bread knife guide: match the rod's diameter to the serrations.

A serrated edge with alternating large and small scallops above a tapered rod, with dashed lines linking a small scallop to the thin end of the rod and a large scallop to the thick end
On a double-serrated or hand-ground edge, expect to slide back and forth along the taper as the scallop sizes change.
↑ Back to all sections

Step by step with a tapered rod

This is the slow, thorough way to do it. Every other tool on this page gets measured against it. Set aside 10 to 15 minutes for a bread knife. The first one takes longer. Chowhound's advice to practice on a cheaper serrated knife before your good one is worth taking.

Set up

  • Sit at a table with a lamp in front of you and slightly to one side, so light rakes across the blade.
  • Put a damp folded towel or a rubber mat down. You can rest the spine of the knife on it, edge up, or hold the knife in the air with your elbow braced on the table. Pick whichever keeps your fingers farther from the edge.
  • Clean the blade if you haven't already. Grit and starch in the gullets clog a rod quickly.
  • Wipe the rod clean. Diamond rods usually work dry or with a little water; follow the rod maker's note.

The method

  1. Color the scallops on the beveled side with the marker.
  2. Lay the rod in the first scallop at the heel so it sits flat against the existing bevel. Serrated bevels tend to be fairly steep, and the marker tells you when you've matched the angle. If the knife maker publishes one, use it.
  3. Slide the rod in until its thickness fills the scallop. A rod that's too thin sharpens only the center; one that's too thick widens the scallop.
  4. Make short, light strokes from the spine side out toward the edge, rolling the rod a little so it sweeps the whole curve. A few strokes per scallop will do.
  5. Once the ink is gone across that scallop's bevel, move to the next one.
  6. Check for a burr on the flat side. Draw a fingertip from the flat face across the edge (never along it) and feel for a slight catch.
  7. Lay the flat side completely flat on a fine stone or ceramic rod and make a few very light strokes to knock the burr off. You don't want a bevel on that side.
  8. Try it on a crusty loaf or a tomato.

Most people go wrong at the angle and the stroke, so those get more detail below.

Marker ink on a serrated blade's scallops with a tapered rod in one scallop
When the ink disappears across the whole scallop, that serration is done.

Matching the angle

Sharpening Supplies says serrated bevels are typically around 20 degrees and that you should match the existing angle; other guides put them at 15 to 20. The marker is how you match it without a protractor:

End views of a one-sided serrated edge with a sharpening rod resting on it three ways: matched to the bevel so the whole face is touched, too steep so only the edge is touched, and too flat so only the shoulder is touched
Two light strokes on a freshly inked scallop tell you which of these three you're doing.
  • Ink gone from the whole ground face: you're on the factory angle. Keep it.
  • Ink gone only at the very edge: the rod is too steep. Lower it toward the blade face.
  • Ink gone only at the top of the grind, near the spine side: the rod is too flat. Raise it a little.

Re-ink and check again after each correction. Once you've found the angle on the first scallop, the rest of the knife is almost always the same, so it goes faster. If you want the numbers for other knives, the angle chart lists them by maker, and every ink pattern is pictured in the Sharpie trick guide.

The stroke

Close-up of one gullet with four numbered stroke positions fanning across the curve from the spine side out past the edge, and a blade strip with twelve scallops numbered from heel to tip
Fan the strokes across the curve so the whole scallop gets sharpened, then move on. Heel to tip, one scallop at a time.

Each stroke runs along the rod, from the spine side out toward and past the edge, with about the pressure you'd use to write with a pencil. Between strokes, roll the rod slightly and shift it a little toward one end of the scallop, then the other, so the rod sweeps the whole curve and not only its deepest point. On a bread knife with big scallops, three or four positions cover it.

Sharpening Supplies sets the order: heel to tip, one serration at a time. Some people work tip to heel. The order doesn't change the result, but sticking to one direction stops you skipping a scallop or doing one twice. The marker helps here too, because any scallop still inked hasn't been done.

A bread knife seen from the beveled side with fourteen numbered scallops; the six nearest the heel are bright steel with check marks and the rest are still black with marker ink
Keep one direction and let the ink show what's left. Re-ink any scallop you're unsure about.

Push strokes or pull strokes? Either. A stroke out toward the edge is the most common advice and the easiest to keep shallow. Chowhound's note about diamond rods is to stroke in one direction only rather than sawing back and forth, which keeps the cut even and saves the diamond.

How many strokes per scallop

The guides disagree, and the disagreement tells you the number isn't the point:

SourceStrokes per scallop
Knife Den3 to 5
Made In4 to 5, then smooth the burr on the flat side
Other how-to guides4 to 6, and as many as 5 to 10
Work SharpNo number; check for a burr every few passes
Two enlarged serrated points: a slightly dull point that is barely rounded and needs a few light strokes, and a point worn flat on a hard counter that needs many more strokes starting on diamond
Stroke counts in the guides vary because knives arrive in different states. A rounded point needs a few strokes; a flattened one needs many.

A slightly dull bread knife might need three light strokes per scallop. One that's been cutting on a granite counter for years might need many more, on diamond. Count only to keep yourself even from scallop to scallop. Stop each scallop when two things are true: the ink is gone across its bevel, and you can feel a small burr on the flat back right behind it.

Can you spin the rod with a drill? Outdoor Life mentions chucking a tapered rod in a drill to speed things up. It works for people with a steady setup, but it removes steel fast, makes heat at the thin points and leaves no time to check the ink. For a bread knife you care about, keep the rod in your hand.

Left: a scallop with the marker ink gone across its whole bevel next to a smaller one with ink still left at the edge. Right: an end view of the edge with a small burr folded onto the flat back
Ink gone by itself can mean you polished the bevel without reaching the edge. A burr by itself can hide a spot you missed. Check both.
↑ Back to all sections

The burr: how you know a scallop is done

When the rod has worked all the way through to the edge, a thin lip of steel folds over to the opposite face. That's the burr. On a serrated knife it shows up on the flat back, right behind each scallop you've sharpened. Feeling it is the only reliable sign you've actually reached the edge rather than just polishing the bevel. The same burr appears on plain edges too (burr guide).

Three end views of a serrated edge: dull with a rounded apex, with a burr folded over to the flat back after rod work, and clean after one light pass with a fine stone held flat against the back
Raise it on every scallop, then take it off the whole flat back at once.

Feeling for it

Put a fingertip on the flat back, well above the edge, and draw it down and off the edge, at right angles to it. Never slide a finger along an edge. A burr feels like a faint snag or roughness as your finger leaves the steel. Untouched scallops feel smooth by comparison, which makes the comparison easy if you check the next scallop over. On small steak knife teeth the burr is tiny; a 10x loupe and a raking light show it as a bright wire line.

Work Sharp's advice is to check every few passes. That's the habit that stops you oversharpening one scallop and undersharpening the next.

A serrated blade seen from its flat back with a green arrow running from well above the edge straight down and off it, and a crossed-out red arrow running along the edge
The motion that finds the burr is also the one that keeps your fingertip out of the scallops.

Taking it off

  1. Finish every scallop first, so you only deburr once.
  2. Lay the flat back completely flat on a fine stone, a fine ceramic rod or a strop. Flat means flat: no lift at the spine.
  3. Make one or two light strokes, edge trailing, along the length of the blade.
  4. Feel again. If a little burr flipped back to the beveled side, give each scallop one very light rod stroke, then one more flat pass on the back.

Outdoor Life describes deburring at a very shallow angle, around 10 degrees. Flat is safer for most people, because any lift adds up to a second bevel on the back, and that's the mistake that weakens the teeth. Chowhound finishes with a leather or denim strap instead of a stone, which is gentler still. A strop works well for the flat back (technique: stropping guide). The Takeout mentions a steel or fine sandpaper for the same job.

A leather bench strop, a purple shaped strop, a bar of yellow polishing compound and a folded sheet of fine wet-and-dry sandpaper lying flat on a wooden board
Any of these takes the burr off the flat back: a leather strop, a shaped strop, or fine paper on a flat surface. The compound bar charges a strop.
↑ Back to all sections

Check your work under light, then with test cuts

A sharpened serrated edge is harder to judge than a plain one because the eye goes to the points. Check three things.

  1. The marker. Any scallop still carrying ink at the edge wasn't finished. Go back to it.
  2. The light. Hold the knife edge-up under a lamp and look straight down. Bright dots on the points mean they're still rounded. A bright line inside a scallop means the edge there is still flat. A sharp edge reflects almost nothing.
  3. The cut. Sharpening Supplies finishes with a test on paper, tomato or rope. At home, start with a tomato, then try a crusty loaf.
TestSharpStill dull
Ripe tomato, no pressureBites the skin on the first drawSlides, then crushes
Day-old crusty loafSaws through crust with light strokes, few crumbsTears the crust, squashes the crumb
Printer paper held by a cornerCuts with a light sawing motionSnags and folds the paper
Cord or twineParts in one or two strokesFrays
A black Sharpie, a silver LED jeweler's loupe and a black illuminated loupe on a folded striped towel, with a Victorinox serrated bread knife lying flat on a wooden board in front
Marker for the bevel, a loupe for the burr and the points. Neither costs much.

If one area still fails, go back to just those scallops. There's no need to redo the whole knife.

↑ Back to all sections

The easier route with a Spyderco Sharpmaker

If scallop-by-scallop work sounds tedious, get the Spyderco Sharpmaker. Its triangular ceramic stones have rounded corners that drop into the scallops. You hold the blade vertical and draw it down each stone, exactly as you would for a plain edge, and the points and scallops get sharpened together. Full details: the Sharpmaker review.

A Spyderco Tri-Angle Sharpmaker base on a granite counter with two white ceramic stones standing in its angle holes, its black case beside it, a Wusthof bread knife lying flat in front and a spare gray stone on the counter
The Sharpmaker's stones sit in fixed angle holes, so the angle is set for you.

How the corner method goes, following Spyderco's own instructions in outline:

  1. Set the stones in the base at the angle that matches the knife. The Sharpmaker has two settings, 30 and 40 degrees inclusive (15 and 20 per side). Ink a scallop and make a few strokes, then keep the setting that takes the ink off the whole bevel.
  2. Turn the stones so a corner faces you, medium grit first.
  3. Hold the knife vertical with the edge down, then draw it down the corner of the left stone from heel to tip, pulling back toward you as you go.
  4. Repeat on the right stone. Alternate sides with the same light, vertical strokes.
  5. Watch the marker as you would with a rod. The rounded corner reaches into each scallop as the blade passes over it.
  6. When you can feel a burr, switch to the fine stones and do a few more alternating strokes, then a few light strokes on the flat faces of the fine stones to tidy the points.
Left: front view of a Sharpmaker with two ceramic stones leaning out at 15 or 20 degrees per side and a knife held vertical against the left stone. Right: a side view of a serrated edge with the rounded corner of a stone sitting inside one scallop
The base sets the angle, so your only jobs are keeping the blade vertical and the strokes light.

Because the Sharpmaker strokes both sides, a one-sided bread knife gets very light work on the flat back too. That's a small trade for the speed, and the fine stones keep it from turning into a real second bevel. Keep the strokes light and the knife truly vertical. Spyderco's explainer on serrated edges offers a different split, about three strokes on the beveled side for every one on the unbeveled side.

Add-ons worth knowing about: Spyderco sells diamond stones for the Sharpmaker for edges that are very dull, and ultra-fine stones for finishing. The base kit handles bread and steak knives without either. If you're choosing between the Sharpmaker and a guided system for all your knives, both are weighed on the best sharpening systems page.

A Spyderco Sharpmaker base with two white ceramic stones and two thin metal rods in its holes, its case beside it, and three more triangular stones, two gray and one white with a red end, lying flat in front
The two add-ons: diamond stones for very dull edges and ultra-fine stones for finishing. Bread and steak knives don't need either.
↑ Back to all sections

Manual pull-through sharpeners with a serrated setting

America's Test Kitchen is blunt about serrated sharpeners in general: many disappoint, and rods can skip across the serrations and miss the valleys. Its recommendations for serrated knives come from the Chef'sChoice family, a manual Pronto model and the electric Trizor XV. For the manual Pronto, the method ATK describes is a few strokes in the first slot, then about five pairs of back-and-forth strokes in the second.

What a manual pull-through does well: it's fast, the angle is fixed, and it gets bite back into the points of a steak knife in under a minute. What it doesn't do: reach into every scallop the way a fitted rod does. Use only the slot the maker marks for serrated or fine work. Chef'sChoice sells manual models labeled for straight and serrated edges at 15 degrees, 20 degrees, or both, so check which angle your knives were ground at before you buy one.

A Chef'sChoice electric sharpener on a kitchen counter with a Chef'sChoice Pronto manual sharpener and a KitchenIQ Edge Grip pull-through lined up in front of it
Electric and manual Chef'sChoice models and a two-slot pull-through. Each has a stage that suits serrations; the coarse stages don't.

Running these machines gets more space in the Chef'sChoice how-to; why the coarse slots worry people is the subject of are pull-through sharpeners bad.

↑ Back to all sections

Electric and pull-through options

A few electric and pull-through sharpeners list serrated knives as supported, including the Chef'sChoice 15XV and the KitchenIQ Edge Grip. On the Chef'sChoice, serrated knives go through the last stage, the stropping stage, and America's Test Kitchen says the flexible stage 3 disk on the Trizor XV reaches into the valleys. On a two-slot pull-through, use only the fine slot. The coarse stages can grind the teeth away.

Left: a three-stage Chef'sChoice electric sharpener with stages 1 and 2 crossed out and stage 3, the stropping stage, checked. Right: a two-slot pull-through with the coarse slot crossed out and the fine slot checked
On a three-stage Chef'sChoice, serrated blades go only through the stropping stage. On a two-slot pull-through, only through the fine slot.

Most grinding wheels and carbide slots touch only the tips of the teeth. The knife bites again quickly, but the scallops themselves stay as they were. Our Trizor XV review and the best electric sharpeners roundup go further on specific machines.

Belt sharpeners and power tools

Outdoor Life's view is that the belt-style electric sharpeners are the only powered option worth using on serrations, because a slack belt can wrap a little into each scallop. Work Sharp's belt machines fall in that group. A belt still removes steel quickly and can round points if you linger, so use the finest belt and keep passes quick and light. A bench grinder or a rotary tool with a grinding bit is a different story: either can overheat the thin points and reshape the teeth in a second. Leave them for workshop tools. Belt work on plain edges is a separate job, and the belt sander guide handles it.

A Work Sharp belt-style electric knife sharpener on a kitchen counter with a spare fine belt lying flat beside it
A belt sharpener. Outdoor Life rates belts the only powered option worth using on serrations, because the slack belt wraps a little into each scallop. Use the finest belt and keep passes quick.
↑ Back to all sections

Guided clamp systems

If you already own a clamp or guided system, check the box before you buy anything. Several include a serrated hone, and it does the same job as a loose tapered rod with the angle held for you.

SystemSerrated toolHow to use it
Lansky Professional kitSerrated medium hone, a narrow ceramic hone on a guide rodClamp the knife, set the angle hole, work one scallop at a time on the beveled side. Walkthrough: Lansky how-to
Work Sharp Precision Adjust EliteConical ceramic rodSet the angle, work each scallop, deburr the back on the fine plate held flat. Details: Precision Adjust review
Work Sharp Guided Field SharpenerCeramic rodHand-held rod work on each scallop; the built-in guides are for the plain edge
Wicked EdgeNo dedicated rodWicked Edge's own advice: coarse lapping film (15 to 30 micron) on the scalloped side at the lowest angle that clears the vise, 15 to 20 light passes, then finer film on the flat side

Wicked Edge's own answer to whether its system does serrations is a qualified yes, and that's the honest summary for most flat-plate guided systems: they're built for plain edges. If you own one, the serrated accessory is fine. If you don't, it isn't a reason to buy one. Our Wicked Edge verdict and Work Sharp vs Lansky cover the systems themselves.

A Lansky sharpening kit open on a counter with colored hone handles, guide rods and a bottle of honing oil, next to a Work Sharp Precision Adjust base and its separate rod on the counter
The pieces that come in guided kits: Lansky's set of hones on handles and Work Sharp's slim rod. Check your box for a serrated hone or rod before you buy a separate one.
↑ Back to all sections

Which method to use

MethodThoroughnessTimeBest for
Tapered rod, scallop by scallopHighest10–15 minGood bread knives
Spyderco SharpmakerHigh5–10 minSerrated kitchen and pocket knives
Guided system serrated rodHigh10 minIf you already own the system
Chef'sChoice stropping stageModerate1–2 minSteak knives and everyday bread knives
Electric / pull-through fine stageModerate (tips)1–2 minInexpensive steak and bread knives
Sandpaper on a dowelLow to moderateSlower than a rodA one-off with no tools

Times are typical ranges, not measurements.

The reason these differ so much is contact. A tool can only sharpen what it touches, and on a serrated edge most tools touch the points first:

Six panels showing a serrated edge against a flat stone, a pull-through slot, an electric grinding wheel, a flexible stropping disk, a Sharpmaker stone corner and a tapered rod, with the contact points marked in red
Red marks where each tool touches. Only the rod and the Sharpmaker corner reach the whole scallop by design.

That's also how to read the reviews that seem to contradict each other. ATK found rods disappointing because they skip across serrations; that happens most when the rod is too thick for the scallop or held at the wrong spot on the taper. A rod sized to the scallop doesn't skip. ATK found the Trizor XV's stropping disk effective because a flexible disk bends into the valleys; a hard grinding wheel doesn't.

↑ Back to all sections

Bread knives and steak knives

If you want to know how to sharpen serrated knives in a set, treat bread knives and steak knives as two jobs. A bread knife has large, deep scallops and takes a tapered rod comfortably. Steak knives often have shallow, fine serrations or a micro-serrated edge, so a rod that fits a bread knife may be too wide for them. Check the teeth before you pick a tool, and use the thin end of the rod on the small ones. The motion is the same either way: work the beveled side, then deburr the flat side.

Three serrated edges one above the other: a bread knife with large deep scallops for the thick part of a tapered rod, a steak knife with small shallow teeth for the thin end, and a micro-serrated edge that is usually not worth sharpening
Look at the teeth first. Bread knife scallops take the thick part of the rod; steak knife teeth need the thin end.

Steak knives are often inexpensive, and a set can be quicker to replace than to sharpen. For a good bread knife, the rod method above is worth the time, and our guide on how to sharpen a bread knife covers that one knife in full. Check first whether it's dull or just gummed up (the check).

Three bread knives lying side by side on a wooden board, handles toward the camera: a Mercer wavy-edge bread knife, a Victorinox Fibrox bread knife and a Zwilling Pro bread knife
Three price tiers, three scallop shapes. The wavy edge on the left has the shallowest scallops of the three.

Bread knife notes

  • Length doesn't change the method, only the time. A 10-inch bread knife simply has more scallops.
  • The first two or three inches from the tip do most of the work on a loaf, so they dull first. Look there before you sharpen the whole blade.
  • The scallops nearest the heel often look untouched. If they cut cleanly, skip them.
  • A popular, inexpensive bread knife like the Victorinox Fibrox has a stamped blade with even scallops, which makes rod work easy. A forged bread knife from Zwilling or Wusthof takes the same method; the steel is often a little harder, so diamond saves time.

Wavy, double-serrated and pointed-tooth edges

Not every bread knife has the classic row of round scallops.

Edge typeWhat it looks likeHow to sharpen it
Scalloped (classic)Round gullets, pointed teethTapered rod sized to each gullet, as above
Wide wavy edgeShallow, wide waves with rounded crests (Mercer's wide wavy edge is an example)Thicker part of the rod, or a Sharpmaker corner; the shallow curve is forgiving
Double-serratedLarge scallops with small teeth inside each one (Wusthof's Classic Ikon double-serrated bread knife is an example)Thin end of the rod for the small teeth, then a light pass with the thicker part across each large scallop; a Sharpmaker corner handles the mix
Pointed or saw teethSharp V-shaped teeth, as on some steak and utility knivesA thin rod or a triangular file for each tooth's bevel; often a replace job
Micro-serratedTeeth too small to see clearly without a loupeUsually not worth it; a pull-through fine slot gives a little bite back
↑ Back to all sections

Steak knife sets: sharpen them or replace them?

A set of six or eight serrated steak knives is a different decision from one good bread knife. The teeth are small, the steel is often softer, and six knives at ten minutes each is an hour.

Five Victorinox serrated steak knives and four straight-edged Wusthof steak knives laid in two rows on a linen towel, blades resting flat and not touching
Steak knife teeth are much smaller than a bread knife's, and some sets are straight-edged. Look closely before you pick a rod.
  1. Sharpen one knife first, all the way, and use it at dinner. If it's clearly better, the set is worth doing. If you can't tell, stop there.
  2. Use the thin end of a tapered rod, or a Sharpmaker corner. The Sharpmaker is the fastest way through a whole set because there's no rod fitting per scallop.
  3. Do all the knives' beveled sides, then deburr all the flat backs in one go on the same fine stone.
  4. For an inexpensive set with fine micro-serrations, a pull-through's fine or serrated slot gives some bite back in a minute per knife. That's a fair trade on knives that cost little.

Made In quotes a custom knifemaker who says a cheap serrated knife may not be worth sharpening at all. We'd put it a little differently: sharpen if one test knife comes back noticeably better, replace if it doesn't. A premium set, Wusthof's Gourmet steak knives for example, is worth the hour.

↑ Back to all sections

Serrated and partly serrated pocket knives

Lots of folders have a combo edge: plain near the tip, serrated near the handle. Do the plain section on your stone or guided system as usual. Then switch to a tapered rod or the Sharpmaker's corners for the teeth. Pocket-knife serrations tend to be smaller and tighter than a bread knife's, so work with the thin end of the rod. Tools that handle both kinds of edge are rounded up in the pocket knife sharpener guide.

A partly serrated folding knife with the serrated section next to the handle marked for the thin end of a tapered rod and the plain section toward the tip marked for a stone or guided system, plus four numbered steps
Plain section first, teeth second, one deburr for the whole flat back at the end.
  • Lock the blade open before you start. On a knife without a lock, stroke edge-first only so pressure never pushes on the spine.
  • Keep stone strokes off the serrations. Start each plain-edge stroke just past the last tooth; a flat stone running into the teeth will flatten them.
  • Spyderco grinds many of its serrations on one face, like a bread knife. Check yours with the same raking-light test.
  • Spyderco's serration pattern mixes large and small scallops. The Sharpmaker's corners handle that mix without changing tools.

The plain-edge side of the job, including locks and the short edge next to the handle, sits in the pocket knife guide. That maker's numbers are on the Spyderco angle page.

↑ Back to all sections

Without a sharpener

Wrap fine wet-and-dry sandpaper (around 600 grit or finer) around a pencil or dowel that fits the scallops, and follow the same steps as with a rod. The unglazed ring on the bottom of a ceramic mug works on the points and the flat side. Neither gives you much control. Both will buy some bite until you can sharpen properly.

A wooden dowel wrapped and taped with fine wet-and-dry sandpaper, a glass plate of graded abrasive strips on a gray mat, an upturned white mug and a Victorinox bread knife lying flat on a counter, with a WhetGuide.com mug behind
The no-sharpener kit: fine wet-and-dry paper taped around a dowel that fits the scallops, graded paper on a flat plate for the back, and the unglazed ring under a mug for the points.
  • Sandpaper on a dowel: pick a dowel whose diameter matches the scallop, like picking the spot on a tapered rod. Tape the paper so it can't spin. Use light pressure, because paper rounds points if you lean on it.
  • Sandpaper flat on a table: good for deburring the flat back. Lay a sheet of fine paper on glass or a countertop and draw the flat back across it once or twice.
  • Mug ring: helps the points and the flat back, not the scallops. Use it as a touch-up before a dinner, not a sharpening.
  • What not to use: a nail file (too coarse and the wrong shape), a flat whetstone on the scallops, a straight honing steel, or the dishwasher's "help."

More stopgaps for plain knives turn up in the no-sharpener guide.

↑ Back to all sections

Safety: the edge you can't see

A serrated knife is easy to underestimate because it doesn't look sharp. Each scallop is a short curved edge, and a rod slipping out of one puts your hand right on the next.

  • Work on a stable surface with a damp towel or rubber mat under the knife.
  • Keep the fingers of your holding hand on the spine or the handle, behind the edge, never under it.
  • Stroke away from your body and away from the hand holding the knife.
  • Feel for the burr across the edge, from the flat back outward. Never along it.
  • A cut-resistant glove on the holding hand is cheap insurance, especially for a first try. It lowers the chance of a cut; it doesn't make a knife safe to grab.
  • Keep rotary tools and bench grinders away from kitchen serrations. They reshape the teeth faster than you can react.
  • Put the knife away before you clean up the grit and the rod.
A serrated bread knife lying flat on a folded damp towel on a rubber mat, with a cut-resistant glove and a tapered sharpening rod resting beside it
Set up before the first stroke: a damp towel or mat so nothing slides, and a cut-resistant glove for the holding hand. The glove lowers the risk; it doesn't remove it.
↑ Back to all sections

Aftercare: keep the points from rounding

The points take nearly all the wear, so aftercare is mostly about what they hit.

A knife in a black Mercer Culinary blade sleeve lying on an Epicurean cutting board, a bamboo in-drawer knife organizer holding knives with steel handles, and a WhetGuide.com mug in the background
A soft board, a sleeve or tray in the drawer, and the dishwasher kept out of it. That's most of it.
HabitWhySource
Cut on wood, bamboo or plasticBoards made of glass, stone or ceramic round the points fastMade In
Don't scrape food across the board with the edgeDragging the points sideways bends and rounds themThe Takeout
Hand wash, dry at onceDishwasher knocks and detergent dull and spot the edgeThe Takeout, Made In
Sleeve, guard or drawer trayLoose in a drawer, the points hit other utensils every time it opensMade In
Saw, don't pressLet the teeth do the work; pressing crushes the loaf and loads the pointsCommon practice

A plastic blade sleeve sized for a bread knife costs little and goes on in a second. If your knives live in a drawer, an in-drawer tray or a guard on each blade keeps the points off other metal. Every knife you own gets a full routine in the knife care guide.

↑ Back to all sections

How often to sharpen a serrated knife

Far less often than a plain edge. Many home cooks sharpen a bread knife once every year or two, and some sources say once or twice a year. Go by the knife, not the calendar.

Three views of the same serrated edge: new, after a few sharpenings with the points slightly lower, and after too many sharpenings with shallow scallops and short teeth, each with the factory edge dashed
Each session lowers the points a little, and the teeth can't grow back. Sharpen when the knife fails a test after washing, not on a date.
UseTypical intervalSign it's time
Bread knife, a loaf or two a weekEvery year or twoTears the crust after a proper wash
Bread knife, daily sourdoughOnce or twice a yearCrushes the crumb, skates on the crust
Steak knives, regular use on platesWhen they stop biting meatPlates are hard; points round quickly
Combo-edge folder, daily carryPlain edge often, teeth rarelyTeeth snag cord instead of parting it
Tomato or utility knifeWhen it slides on tomato skinThe tomato test fails after washing

Sharpening too often wastes steel. Each session takes a little off every point, and a serrated knife has no spare height to lose. The plain-edge schedule lives on the how often to sharpen page.

↑ Back to all sections

Replace or sharpen? A decision by knife

KnifeScallopsRecommendation
Forged premium bread knife (Zwilling Pro, Wusthof Classic)Large, evenSharpen with a rod or Sharpmaker. Worth every minute.
Stamped mid-price bread knife (Victorinox Fibrox, Mercer)Large or wavySharpen. The rod method is easy on even scallops.
Premium steak knife setSmallSharpen one, then the set if the test knife improves
Budget steak knife setSmall or microFine slot of a pull-through, or replace
Combo-edge pocket knifeSmall, mixedSharpen; Sharpmaker or thin rod
Knife with broken or missing teethDamagedA pro can regrind it; otherwise replace
A chart with tooth size across and knife quality up the side: forged and stamped bread knives and a combo-edge folder sit in the sharpen zone, a premium steak set is a test-one-first case, and a budget steak set sits in the fine slot or replace corner
Read across for tooth size and up for knife quality. The top left is worth your time; the bottom right usually isn't.

A professional service is a reasonable middle path for one good knife you don't want to practice on. Ask first: not every service takes serrated edges, and some charge extra. Our service cost guide and mail-in service roundup have the details. Knives and Tools adds that on cheap cutlery a new knife is often the better option, and that serrated knives rarely need to be razor sharp.

↑ Back to all sections

Mistakes to avoid

The worst one is sharpening the flat side as if it were a straight edge. That puts a second bevel on the knife and weakens the teeth, so only deburr that side, and keep it flat.

Four panels: a flat whetstone flattening the points, a coarse pull-through slot chewing off teeth, a new bevel ground onto the flat back, and a rod too thick for the scallop resting on the points
Each of these takes steel off in the wrong place, and none can be undone at home.
  • A flat whetstone on the scallops just grinds the points down.
  • The coarse slot of a pull-through can take the teeth off.
  • Sharpening too often wastes steel. Wait until the knife tears bread instead of cutting it.
  • A rod too thick for the scallop rides on the points and widens the gullet. Move to the thinner part of the taper.
  • Pressing hard. Light strokes cut cleanly; heavy ones round the points and tear sandpaper.
  • Skipping the clean-up. Sharpening a gummed-up knife takes steel off a blade that only needed a wash.
  • Leaving the burr. A burr folded over the flat back makes a freshly sharpened knife feel dull.
A serrated bread knife with a dark wooden handle lying on a board beside a sourdough loaf with three even slices and scattered crumbs
A sharp bread knife leaves even slices with the crust intact instead of a crushed loaf.
↑ Back to all sections

Troubleshooting: still not cutting?

What happensLikely causeFix
Still tears bread after sharpeningBurr left on the flat backOne or two flat passes on a fine stone or strop
Cuts at the tip, tears near the heelSome scallops missedRe-ink, find the scallops that kept their ink, do those
Skates on tomato skinPoints still roundedA few more rod strokes reaching right to the points, or a Sharpmaker pass
Ink only gone at the very edgeRod held too steepLower the rod toward the blade face
A groove in the middle of each scallopRod too thin for the scallopMove to a thicker part of the taper and roll the rod
Scallops look wider and teeth shorterRod too thick, or too much pressureThinner part of the taper, lighter strokes
Shreds the crust, lots of crumbsUneven teeth after a coarse pull-throughRod work on each scallop to even them up
Feels sharp, dulls in a weekGlass or stone board, or the dishwasherSee aftercare
↑ Back to all sections

Serrated knife cheat sheet

1. Clean and checkHot soapy wash, brush the gullets, dry, tomato test.
2. Find the bevelThe face with scallops ground in. The other is flat.
3. Fit the rodSlide in until it fills the curve. Work at that spot.
4. Burr, then deburrShort strokes to a burr, heel to tip. One flat pass on the back.
QuestionShort answer
Which side?The beveled side. Deburr the flat back only.
What angle?Match the factory bevel; typically around 15 to 20 degrees
Rod size?The spot on the taper that fills the scallop
How many strokes?Until the burr appears; often 3 to 10
Whetstone?Only for deburring the flat back
Electric?Final or serrated stage only
How often?Every year or two for a home bread knife
Worth it?Yes for a good bread knife; test one before a cheap steak set
↑ Back to all sections

Pick a method by the knife

Flowchart: if the knife no longer tears bread after washing it was only gummed up; if it is not worth keeping, replace it or use a pull-through's fine slot; with several serrated knives use a Sharpmaker; with a guided system use its serrated rod; otherwise use a tapered rod scallop by scallop
Four questions get almost everyone to the right tool.

A bread knife you care about deserves the tapered rod: 10 to 15 minutes once every year or two is a fair trade. If you have a drawer of serrated steak knives and a combo-edge folder, buy a Spyderco Sharpmaker and do them all the same way. Your straight-edge knives need different treatment; start with the angle chart and our best sharpening systems.

If the knife is a budget steak knife with teeth you can barely see, don't spend an evening on it. The fine slot of a pull-through, or a new set, is the sensible call.

Two pairings on a wooden board: a Victorinox bread knife beside an open DMT Diafold tapered rod, and a budget serrated steak knife beside a KitchenIQ two-slot pull-through sharpener
The verdict in one picture: a good bread knife gets the tapered rod; a budget steak knife gets the fine slot or a new set.

Technique reflects standard sharpening practice and the makers' and publishers' guides named on this page; product details come from Amazon listings and maker pages, checked November 14, 2026. How we research · Affiliate disclosure

Questions people ask

Can you sharpen a serrated knife?
Yes. Use a tapered rod (ceramic or diamond) sized to fit the scallops, sharpen each serration on the beveled side at its existing angle, then lightly remove the burr from the flat side. A Spyderco Sharpmaker, the serrated rods that come with some guided systems, and a few electric sharpeners with a serrated setting also work.
Which side of a serrated knife do you sharpen?
Most serrated kitchen knives are ground on one side only. Sharpen the beveled side, where you can see the scallops ground in, and only flatten the burr on the other side with a few light passes. If scallops are ground into both faces, give each side the same light rod work.
Can you sharpen a serrated knife with a whetstone?
Not well. A flat stone only touches the points of the serrations and grinds them down. You can use a fine stone to deburr the flat back, held dead flat, but the scallops need a rod that fits inside them.
Can an electric sharpener sharpen serrated knives?
Some can. Chef'sChoice lists serrated knives as supported on models like the 15XV and Trizor XV, using the final stropping stage, and America's Test Kitchen says the Trizor XV's flexible stage 3 disk reaches into the valleys. Most grinding wheels touch the tips of the teeth more than the scallops, so a rod is still more thorough.
How often should you sharpen a serrated knife?
Far less often than a straight edge, because the points do most of the cutting and protect the scallops. Many home cooks sharpen a bread knife once every year or two. Sharpen when it tears or crushes bread after a proper wash, not on a calendar.
Is it worth sharpening a cheap serrated knife?
For a very inexpensive knife or a budget steak set, replacing it can be easier. A good bread knife is worth the 10 to 15 minutes a tapered rod takes. Fine micro-serrations on cheap steak knives often aren't worth sharpening at all.
How many strokes per serration?
Guides disagree: Knife Den says 3 to 5, Made In 4 to 5, and others go as high as 10. The real stop signal is a slight burr on the flat back along that scallop. Use short, light strokes and check for the burr every few passes.
What angle do you sharpen a serrated knife at?
Match the angle the factory ground. Sharpening Supplies says serrated bevels are typically around 20 degrees, and other guides give 15 to 20. Color the bevel with a marker, make two light strokes and adjust until the ink comes off evenly.
What size sharpening rod do I need for a serrated knife?
A tapered rod covers most sizes. The DMT Diafold serrated sharpener tapers from about 1/16 inch at the tip to about 1/4 inch at the base, according to Sharpening Supplies. Slide the rod into each scallop until it fills the curve and work at that spot.
Can you use a honing steel on a serrated knife?
Not on the scallops. A straight steel or straight ceramic rod is too wide to get into them and only skips across the points. A fine ceramic rod is fine for the flat back, held flat to knock off a burr.
Can you sharpen a serrated knife with sandpaper?
Yes, as a stopgap. Wrap fine wet-and-dry paper, around 600 grit or finer, around a dowel or pencil that fits the scallops and follow the rod method. Lay a sheet on a flat surface for the flat back. It gives less control than a rod.
How do you sharpen serrated steak knives?
The same way as a bread knife, but with the thin end of a tapered rod because the teeth are smaller. Do one knife first and try it on a steak before you do the set. Fine micro-serrated steak knives are often cheaper to replace than to sharpen.
Why does my bread knife crush the loaf?
Either the points are rounded or the scallops are packed with starch and grease. Wash the blade with hot soapy water and a brush, dry it, and try again. If it still tears or crushes, it needs sharpening.
How do you sharpen a partly serrated pocket knife?
Sharpen the plain section on your stone or guided system first, stopping before the first tooth. Then do the serrations one at a time with the thin end of a tapered rod on the beveled side, and finish with a few light, flat passes on the back to remove the burr.
What is a burr and why does it matter on a serrated knife?
A burr is a thin lip of steel that folds over to the flat back when you have sharpened right through to the edge. Feeling it tells you that scallop is done. Leaving it on is a common reason a freshly sharpened bread knife still tears, so remove it with one or two flat passes.
Can you sharpen a serrated knife with a Sharpmaker?
Yes. Spyderco's Sharpmaker uses triangular ceramic stones whose rounded corners drop into the scallops. Hold the blade vertical and draw it down the corner of each stone, alternating sides as Spyderco's instructions describe. The flat faces catch the points at the same time.
Can you sharpen a serrated knife with a pull-through sharpener?
Only with a slot made for serrated edges, and only the fine stage. Coarse carbide slots can take the teeth off. A pull-through mostly touches the tips, so the knife bites again quickly but the scallops stay as they were.
How long does it take to sharpen a serrated knife?
About 10 to 15 minutes for a bread knife with a tapered rod, done scallop by scallop. A Sharpmaker usually takes less, and the fine stage of an electric or pull-through sharpener takes a minute or two.
Do serrated knives need honing?
Not in the usual sense. You can't run a steel through the scallops. A few light passes on a fine ceramic rod held flat against the back, now and then, will knock off any folded edge. Keep the knife off hard surfaces and out of the dishwasher and it will need little else.
Can you send a serrated knife out to be sharpened?
Yes. Many sharpening services and some knife makers will sharpen serrated blades, often with a dedicated machine or rod. Ask before you send it; some services charge more for serrated edges or don't take them.